How To Build A Simple Dog Ramp

How To Build A Simple Dog Ramp
Edward R. Forte October 16, 2021

Ramps

How To Build A Simple Dog Ramp

Cut the Parts.Using a jigsaw, cut the parts of the box, top and legs to length according to the measurements on the cut list.On the long 1x5 sides of the box, mark the edge 2 inches from one end and 10 inches from the other end.The shorter cut will be at the back, or top, of the ramp where it meets the edge of the bed.Cut the Legs.Using a drill driver fitted with a 3/8-inch drill bit, bore a hole at the back end of each long side that's 1½ inch from the bottom edge and 3½ inches from the shortest point at the back of the box.Drill Bolt Holes in the Legs.Drill a 3/8 inch centered hole 13½ inches from the bottom of each leg.Screw the leg crosspiece between the legs with the ends of the crosspiece flush with the back edge of the legs.Bolt the Legs to the Box.Insert a 3/8-inch bolt through the leg and box using a washer on the outside of the leg, four washers between the leg and the box, a washer on the inside of the box, and a locking nut on the end of the bolt.Fasten a block to the underside of the lid, ½ inch from one end.Center the box between the sides of the lid and so that the ends sit flush with the ends of the lid.Using a drill/driver, secure a 30-inch piano hinge, knuckle side out, to the side of the box.Attach the other end of the folding hinge to the front edge of the leg.Mount nonslip rubber strips or pads on the bottom of each leg and skid feet to the crosspieces on the underside of the box and to the back of the crosspieces between the legs.Cut a nonslip rug, like the sisal shown here, to the size of the lid.Work your way from one end of the lid to the other until the rug is secure. .

Saturday Morning Workshop: How To Build A Collapsible Dog Ramp

Introduction We all love our dogs to be at our side, but when they age and can no longer jump up to a bed or other places they once could, it can break an owner’s heart.Or your pup may simply be too small to access those places throughout its life.This bedside dog ramp is a sturdy, reliable project that you can build in an afternoon. .

15 Free DIY Dog Ramp Plans For Bed, Car, Couch, Stairs

Then maintain the good health of them using these DIY Dog Ramp plans that will make it easier for your dogs to reach the elevated spaces of bed.It will keep your dogs safe from the injurious falls, too!Make also recycled cardboard boxes ramps, will simply cost you nothing.As these dog ramps will avoid putting pressure or stress on joints, so they will take the entire long life and safety of your dogs.Most of these DIY Dog Ramps for beds are to make with the wood.Opt for pine or lumber wood slats to build the overall frame.Check out all the budget-friendly options to build a dog ramp by taking a roundup of the entire list of dog ramps.Grab the 1x2x8′ board, plywood, small hinges, and 3/4” dowel with 14” length to build this adjustable dog ramp.it provides a handle for easy carriage, and don’t forget to provide the carpet to the sloped floor of this wooden dog ramp.This will be a play station too to keep your dogs physically fit.First, cut the rail and cover it up with plywood.Ensure better joint health of your dogs by building this dog ramp, will easily make him reach the higher furniture surfaces in the home.Use Silhouette store dog paw print to adorn the ramp more.Here you will also see better use of an old carpet.It will make the best gift for a pet lover at home.The best accessory to ensure better health and longevity of your dog.Use an old piece of carpet to cover it now.Yes, just build this dog ramp that will allow a puppy to instantly reach a bed without putting extra pressure on the muscles.This DIY dog ramp for stairs will make it easier for your dog to come out from your home and to enter in after a playing session outdoor.You can install it as a sloped surface for your dog, will assist reach the higher levels easily.The best playing prop for your dog is a paw ramp.Get here the free video instructions to build a gorgeous looking ramp out of recycled materials?Build your dog a house of their own with these free DIY dog house plans that include diagrams, photos, building instructions, and supplies/cut list.Buying custom one may get expensive, but these free ideas will make it easier for you to get a custom DIY dog ramp in no time and in a budget-friendly way. .

How to Build a DIY Dog Ramp

The Crash Course on DIY Dog Ramps for Beds, Stairs, Cars, and Beyond.There are numerous reasons why your dog may need a dog ramp — from their tiny stature and skeletal issues to old age and disabilities — but the truth of the matter is that you need one too.A dog ramp can ease your doggo’s climbing up and down the stairs or a piece of furniture, but it also eliminates the need for you to pick them up and carry them around constantly.A commercial dog ramp that is well-built and reliable can come with a hefty price tag, especially if you want it to be foldable, adjustable, or have any other practical functions.With the help of Alpha Paw, you can make a functional, durable, and sturdy DIY dog ramp that will also be customized to your home’s layout and decor.You’ll be able to make an ideal ramp that will be the perfect addition to any part of your home, as well as your car or yard.There’s no point in building a dog ramp that won’t be suitable for your canine or one that they won’t deem secure enough to use.Even if your dog is a picture of health, if they are a small or miniature breed, they will benefit from strutting what their momma gave them down their own little runway.Yorkies, Doxies, Chihuahuas, and many others are prone to back problems that can be severely exacerbated by jumping from overly high surfaces and down endless flights of stairs.Make sure you also adjust the width of this ramp to your pooch’s wheelchair or any other need they may have.In case you have more than one dog who needs ramps with different inclines, instead of buying one for each pooch, invest in an adjustable dog ramp.You can make a dog ramp from various materials, but the choice will depend on your fluffer’s weight:.Metallic ramps are likely going to corrode if left in the rain, so they are not the best option if you want to make a long-lasting outdoor ramp.They are lightweight and portable, so it comes as no surprise that wood is the material of choice for most DIY dog ramps.You need to determine whether your ramp will stay put in one place — such as over indoor stairs or out on the patio — or whether you need one that you can move from your bed to the sofa to the armchair.All you need for them is the right material and simple design.Granted, if what you need is a vehicle ramp, you can freely skip this step, but indoor ramps affect the overall appearance of your home and are just as important as any other item in it.Now that you’ve adequately prepared yourself for this creative endeavor, the time has come to have some fun and build your pooch the ramp of their dreams!— go for an ¼ inch thick board or more, depending on the dog’s weight Two hardwood side beams.You should end up with two sides and a walkway custom made for your pooch’s needs.Avoid gluing these pieces together as that will make the ramp less stable and more likely to break apart pretty soon.This part is essential because your pup’s paws are soft and fuzzy, which is why they could slip on the smooth wooden surface of the ramp.This is a good idea for outdoor ramps, such as those used over stairs on a deck or porch, as the carpet would soak in rainwater and cause the plywood beneath to rot quickly.Double-check to see if anything is wobbly or shaky — if it isn’t, congratulate yourself on a job well done and see how your pooch likes their ramp!Make adjustable footing so that you can have better control over the ramp’s incline.Here at TheDodDigest, we are obsessed with multifunctional pieces, so we’re going to show you an easy way to transform the ramp discussed above into a handy little bedside cabinet for your bedroom.Avoid the cardboard ones as they aren’t sturdy enough for a DIY dog ramp.Arrange them as you see fit, but make sure that they cascade in a way that keeps to the incline you choose for your goggie’s ramp.Having a hinge gives you more leeway to adjust the incline later on as your pup ages or if you find that the ramp is too steep for them after all.You can add more crates below to decrease the incline or vice versa.The crate shelves are super handy for storing bedding, throws, shams, books, or even your doggo’s leash, collars, and toys!All you’ll need are some additional boards or pre-made doors, more hinges, and several extra screws! .

DIY Dog Ramp

Our loveable lug Great Pyrenees is going on eight years old, and like most other giant breeds he is starting to slow down a little bit.We first noticed he wasn’t able to leap into the truck anymore so now Hubs hoists him in, then he hurt himself on the hardwood floors, and recently he slipped going up the two stairs to our patio.So when the Farmhouse Hens topic for July is outdoor projects, I knew exactly what we were going to make.You will find the link to their posts after mine.This DIY dog ramp is built to lay against the existing stairs, so you don’t need to update and cut into existing stairs.They are really simple to make, I found some shortcuts for part of the measuring that would likely make a carpenter cringe.This one is two feet wide because our boy is big and the two feet width fit between the existing stair brackets.I went outside with a measuring tape and a scrap board so I could visualize the incline and decided four feet was doable for him.Check out the picture above to see what I am referring to, the completed ramp did a better job of illustrating what I mean, but to figure it out we took two lengths of 1 by 2 scrap lumber outside in the rain.Don’t fret too much about getting everything figured out perfectly before starting.You will need the following lumber, 1/2″ or thicker plywood 2′ by 4′.Doing this looked really weird, so we checked it by laying the pieces together first before drilling and screwing them in.For extra strength place in cross pieces, its true you might not need to do this for a small dog, but I recommend doing it anyway as you never know when someone would “try” the ramp.To finish the dog bed I gave it two coats of leftover greyish paint we had left over from the front porch.Here is a post about how I store and mark my paint, it does end up saving us quite a bit and its so much easier than going and shopping for little projects like this one.To give pup extra traction we purchased a cheap rug at Home Depot for $10, I made a dog paw stencil using the silhouette and just paper.That and a bunch of treats should make the change easier for him.Wish me luck, my big boy has a mind of his own. .

Build DIY Pet Steps ‹ Build Basic

Give your pup a leg up with these easy-to-assemble pet steps.With plywood sides and simple 1×2 cleats to hold the pieces in place, you’ll be pleasantly surprised how easily the parts come together.Cut List Cost: $28 $28 Time: 3 hours Difficulty: Moderate.(1) ½” x 2′ x 4′ Birch Plywood to make the Sides and Treads (1) 1 x 2 x 8′ to create the Cleats and a Support Bar across the back (1) 1 x 6 x 6′ to create the Risers and a Support Bar across the back (3) ½” x 2″ x 4′ Boards to Trim the Sides (Optional) Wood Glue 1¼ inch Finish Nails to attach the Risers, Treads and Support Bars 1 inch Finish Nails to attach the Cleats ¾ inch Finish Nails to attach the Trim (optional) Fabric to make a Stair Runner (optional) Drawer Liner to cushion beneath the Runner (optional) Hand Stapler and 3/8-inch staples to attach the Runner (optional) ½ inch Plywood Sides – 2 @ 17¼” H x 24″ W ½ inch Plywood Treads – 3 @ 13¼” W x 8″ D 1×6 Risers – 3 @ 13¼ inches 1×2 Support Bar – 1 @ 13¼ inches 1×6 Support Bar – 1 @ 13¼ inches ½” x 2″ Trim – Cut to Fit 1×2 Cleats 1×2 Riser Cleats – 6 @ 5½ inches.Since you lose about an 1/8-inch per cut, the parts should end up measuring two at 17 inches and one at 13½ inches, all by 24-inches-wide.Cut the middle section into three 8-inch-wide Treads.Using a circular saw cut along the line on each plywood Side.Align a 5½-inch Riser Cleat inside the line on each board.Starting low and working up the “steps”, apply wood glue to the back of each Cleat, and then nail it in place.Additionally, there should be a ¾ inch gap behind the cleat to allow room for the Support Bar to be installed later.Apply wood glue to the top edge of each horizontal Cleat and the top edge of each Riser.Repeat Step 10 to install the remaining Treads.Nail two 1 ¼ inch nails through each Side and into the ends of the 1×2 to hold it in place.(Note: I didn’t mind nailing though the Sides because I knew it’d be covered with trim.If you don’t plan to install trim, a Kreg Jig can be used to make pocket holes in the 1×2 so that the fasteners remain hidden.).Lay the ½” x 2″ trim in place to mark each cut as you work around the perimeter of each Side.Using a miter saw, cut the boards to fit.I left a half inch boarder around each piece, and secured it using a hand stapler so it could be easily removed and replaced, if needed. .

How to Build a DIY Foam Dog Ramp

Your furry child can finally climb the couch without much struggle, and you are happy to see them getting there safely.You will be able to use it in your home or even outdoors.They probably all vary in height, which means that you will be able to use the ramp for only one of these.What we know for sure is that you are going to need lots of foam.This way, you will avoid exposing your hairy companion to getting spine curvatures.If you have a Sausage pooch in your home, here’s our suggestion for the best Dachshund ramps.If you make the incline too steep, your pooch will be afraid to set a paw on it.You can make a ramp’s incline based on our following guidelines below.Always have in mind that your dog should feel comfortable walking on the ramp.You need to think about keeping your dog’s joints healthy and reducing the pain they might have.You need to use non-slip fabric that will provide your hairy pal with stability.Your pooch is a clumsy little beastie who usually runs over the ramp.You don’t want to see them sliding off of it all the time.Foam ramps coated in any material can get slippery on a hardwood floor and slide when your pooch starts using them.Foam is like bread—it’s bubbly, lightweight, and it can be cut with a knife.To make a smoother slit, don’t cut the foam but score it instead, while pressing lightly.Some pups even choose to sleep on it, which is super cute.As we’ve already mentioned, you can use a different material for coating the foam.Now, you should not use glue and staple guns to cover the foam with fabric.Some people have tried pinning the fabric to foam, but this is highly unsafe for your dog.We advise you to make a zip-off ramp cover, as it will be much easier for cleaning and washing.You need to get them acquainted with the new object first, so prepare yourself for baby steps.The crucial part of every dog training session is positive reinforcement, which your pooch receives through praise and treats.Getting your gorgeous woofer used to a new ramp usually takes these three steps:.You can put a treat on the ramp and let them eat it, but don’t repeat this too often.Again, you can show them a treat and give it to your pooch once they climb.You shouldn’t train your dog for too long, or they will lose focus from the activity.Your woofer will get tired and associate the ramp training with negative emotions.Repeat each step until you feel that learning has started to sink in.Train your pooch several times a day, but avoid working with them around meals.Every dog is different and needs some time to process the new information.There are several more serious health issues that require obligatory ramp use, such as:.Any sudden movements can cause them pain, which is why they need your help.If, at some point, your precious baby got themselves injured, don’t think twice about getting the ramp.This condition often appears with dwarf pooches, such as Dachshunds, who are more susceptible to back problems than any other breeds.Dogs who suffer from IVDD can’t move around the house without a ramp.Dogs are family members, and our homes should also be adjusted according to their needs.If you decide to go make a foam dog ramp, follow our guidelines, and you will be able to sleep tight, knowing that your little woofer is roaming safely around the house. .

15 DIY Pet Stairs, Ramps, & Steps You Can Build Today (with

Pet ramps or stairs are a great way to allow an older pet easier access to different parts of your home.Building your own pet stairs and ramps can easily solve these problems because this is inexpensive, they can be built to your exact specifications, and it’s a fun and easy weekend project.Simple wood steps.A few 2x4s, a dozen screws, and sandpaper are all you need to make a great-looking set of steps for your pooch!It is simple to make, consisting of a ramp of carpeted wood and a wooden base with a hinged stand in-between.Crate pet steps.We love designs that have more than one use, and these dog stairs double as an adorable dog kennel underneath for your pooch to get privacy.While this may be slightly more complicated to build, having a stair and kennel combination is a great addition for any indoor pooch.The kennel is located directly underneath the steps to provide more space and make the steps far easier to build.If you don’t want your pet sleeping on the bed with you, this pet stair and bed combination is ideal.This project is a great idea, as it combines various sizes of storage and shelving with a carpeted ramp for your pet.The ramp is easy and inexpensive to build and is the perfect way to reduce clutter while allowing your beloved pet access to a cozy bed!The storage space can also double as an extra kennel space for your pet to snooze.This simple pet step doubles as a step and bed and is made from a vintage suitcase — these are easy to find and inexpensive.The bed looks great, and with the suitcase handle, it is easy to move and take with you on trips!If you are looking for a quick, inexpensive, and simple pet ramp, this carpeted DIY ramp is just the ticket.Sheets of plywood, a few screws, and a bit of carpeting are all that’s needed to create a pet ramp in a few hours or less.From simple cardboard box steps to complicated storage ramps, any of the above ideas will allow your pet access to the bed, sofa, or car, and you can add extra storage space! .

Share

Related

Dog Stairs For King Bed

Dog Stairs For King Bed.

Easy to put together What We Don't Like Only 22 inches high These steps are ultra-versatile which makes them a top choice for owners with more than one pet or those with changing needs.The rise of each step is 6 inches high.Low step rise What We Don't Like Only 18 inches high These plastic steps are covered by a removable, washable cover, which makes it easier for your pet to climb up with a sure footing.Space-saving design What We Don't Like Cumbersome to move With shorter, deeper steps and a 5-inch rise, these stairs are made for smaller pups, especially those dogs with shorter legs.You’ll appreciate that it’s hollow inside, which means not only is it light to carry around, but it also has storage space under the hinged back panel—just the place to store your pup’s toys and maybe even a treat or two.It’s easy to put together, has rubber grippers on the bottom to secure the steps in place, and the carpet treads can be removed and tossed in the washing machine.As for the foam, it’s made in the USA with premium-grade materials and CertiPUR-US, so you don't have to worry you’re exposing your pet or home to chemicals of concern.Best for Small Dogs: Sandinrayli Pet Easy 3 Steps View On Amazon View On Sandinrayli.com Dimensions: 17.7 inches x 13.8 inches x 11.8 inches | Maximum Weight: Up to 55 pounds | Number of Steps: 3 | Material: Plastic frame, micro suede cover What We Like Lightweight.Easy to put together What We Don’t Like Slides around on hard surfaces It will be a short one, two, three hop on up to the sofa for your smaller dog, puppy, or cat with this set of steps.Each landing is a nice and wide 5.9 inches which will make your pet feel secure as they make their way up each 3.9-inch rise.The plastic stairs are lightweight and easy to move from space to space (say from the living room to the bedroom) and are covered in a soft material that’s removable and washable.You could also try it outside to help your pup reach your deck, just note that if you do, since it’s black, you’ll want to keep it in the shade, so it doesn’t burn your pooch’s paws.

Portable Dog Ramps For Stairs

Portable Dog Ramps For Stairs.

If you have a tiny dog, a pet that is recovering from injuries or surgery, or a senior pal in your household, dog steps and ramps might be worth looking into.Keeping around a set of steps for dogs or a dog ramp can make all the difference to your faithful companion.Indoor pet stairs provide easy access to sofas, chairs and beds.It all depends on the size of your dog and where he wants to go.In your search for the best dog ramp, look for one that supports your pet's weight range, has a soft or non-slip surface, is lightweight, and includes rubber feet to prevent the ramp from slipping.With all of the choices for dog steps and ramps that you can find on Chewy, there's no excuse for not finding the perfect one for your pet.The best stairs for dogs will depend on the size, age and condition of your pup and on the application you’re using them for.You can use dog stairs for cars, but ramps are usually the go-to for autos because they fold easily and compactly for travel.

Dog Ramps For Cars And Trucks

Dog Ramps For Cars And Trucks.

Whether you’re like us and take your pooch with you on every trip to the supermarket or your pet’s travels are limited to vet visits, you’ll eventually need a convenient way to get Fido in the vehicle.This is especially true if he’s injured or getting on in years, and jumping right in is out of the question.Learning how to build a dog ramp like the ones below, are fast and easy to make, and they make getting in even the tallest cab painless for both you and your dog.This highly-portable ramp from Pet Life Academy doesn’t fold, so you’ll need to leave plenty of room in the trunk or pickup bed for it.However, it’s extremely stable and durable, so your pooch shouldn’t have any misgivings about scurrying on up.This plan from Best Net Review results in a ramp that’s adjustable, stable, and easy to customize, so you don’t have to look at an ugly old plank every time you go for a drive.It takes a little more work than slapping down a basic board, of course, but the results are well worth it.If you care more about functionality than flair, this option from This Old House is quick and easy to make.Despite being incredibly easy to build, this ramp from Instructables is also incredibly versatile and can help your dog get on the bed just as well as it helps him climb in the car.If the thought of getting out a saw and working with wood fills you with dread, this is the design for you.While nominally an indoor ramp, this creation from My Repurposed Life works just as well for getting Fido in and out of the car, due to the long plank at the top that makes scrambling onto the seat a breeze.You’ll simply need to modify the instructions to make the ramp taller, but that’s not much of a hassle at all.Like the one from My Repurposed Life, this ramp from Irresistible Pets is intended for indoor use, but that doesn’t change the fact that it’s perfect for helping a pooch into a pickup.This Salt of America ramp is incredibly stable, so injured pets will feel confident scurrying up and down on it.It’s a little longer than some other models shown here, but that just prevents your pup from having to climb up at a steep angle.Dogsaholic has several ideas for ramps, but this one is specifically intended for getting in and out of vehicles.We especially like the addition of an eye hook at the top to prevent it from slipping and sliding.Sarah Leamy offers up this no-frills option, which has plenty of footholds for your pup, not to mention an incredibly stable base.This model requires very little woodworking skill, but you’d never know it from the finished product.You’ll have to buy the instructions for this ramp from Make and Build Dog Stuff, but the cost is well worth it, as the plans are more detailed and easier to follow than some other options.In addition to step-by-step instructions, you’re also going to get colored 3D drawings showing you how everything should look during the assembly process.Don’t let any squeamishness about your woodworking skills prevent you from making a ramp for your furbaby, as most of the options above are remarkably easy to make — and your dog will thank you for them.After all, what’s easier: taking an hour or two to learn how to build a dog ramp, or spending weeks in physical therapy after you throw your back out lifting Fido into the truck?Check out our favorite boat ramps for dogs here.